1. 首页首页
  2. 编程汇总编程汇总

配置二层交换机Vlan_华为模拟器交换机配置

编程汇总 • • 阅读 16

配置二层交换机Vlan_华为模拟器交换机配置使用 access 接口 拓扑图 LSW1 system view 进入系统视图 Huawei sysname LSW1 修改设备名称 LSW1 vlan batch 10 20 创建 VLAN10 20 LSW1 int g0 0 2 进入端口 LSW1 GigabitEther 0 2 port link type access

使用access接口

拓扑图：

LSW1：

system-view     //进入系统视图

[Huawei]sysname LSW1    //修改设备名称

[LSW1]vlan batch 10 20    //创建VLAN10 20

[LSW1]int g0/0/2    //进入端口

[LSW1-GigabitEthernet0/0/2]port link-type access    //设置access接口

[LSW1-GigabitEthernet0/0/2]port default vlan 10    //设置默认vlan为10

[LSW1-GigabitEthernet0/0/2]dis this    //查看当前的配置

#

interface GigabitEthernet0/0/2

 port link-type access

 port default vlan 10

#

return

[LSW1-GigabitEthernet0/0/2]

[LSW1]int g0/0/3

[LSW1-GigabitEthernet0/0/3]port link-type access 

[LSW1-GigabitEthernet0/0/3]port default vlan 20

[LSW1-GigabitEthernet0/0/3]dis vlan    //查看vlan

[LSW1-GigabitEthernet0/0/3]quit 

save     //保存

The current configuration will be written to the device.

Are you sure to continue?[Y/N]y    //Y

Now saving the current configuration to the slot 0.

May 27 2022 15:14:07-08:00 LSW1 %%01CFM/4/SAVE(l)[1]:The user chose Y when decid

ing whether to save the configuration to the device.

Save the configuration successfully.



[LSW1]int g0/0/1

[LSW1-GigabitEthernet0/0/1]port link-type trunk 

[LSW1-GigabitEthernet0/0/1]port trunk allow-pass vlan 10    //允许vlan10通过

[LSW1-GigabitEthernet0/0/1]port trunk allow-pass vlan 20    //允许vlan20通过

save

LSW2:

system-view     //进入系统视图

[Huawei]sysname LSW2    //修改设备名称

[LSW2]vlan batch 10 20    //创建VLAN10 20

[LSW2]int g0/0/2    //进入端口

[LSW2-GigabitEthernet0/0/2]port link-type access    //设置access接口

[LSW2-GigabitEthernet0/0/2]port default vlan 10    //设置默认vlan为10

[LSW2-GigabitEthernet0/0/2]dis this    //查看当前的配置

#

interface GigabitEthernet0/0/2

 port link-type access

 port default vlan 10

#

return

[LSW2-GigabitEthernet0/0/2]

[LSW2]int g0/0/3

[LSW2-GigabitEthernet0/0/3]port link-type access 

[LSW2-GigabitEthernet0/0/3]port default vlan 20

[LSW2-GigabitEthernet0/0/3]dis vlan    //查看vlan

[LSW2-GigabitEthernet0/0/3]quit 

save     //保存

The current configuration will be written to the device.

Are you sure to continue?[Y/N]y    //Y

Now saving the current configuration to the slot 0.

May 27 2022 15:14:07-08:00 LSW1 %%01CFM/4/SAVE(l)[1]:The user chose Y when decid

ing whether to save the configuration to the device.

Save the configuration successfully.



[LSW2]int g0/0/1

[LSW2-GigabitEthernet0/0/1]port link-type trunk 

[LSW2-GigabitEthernet0/0/1]port trunk allow-pass vlan 10    //允许vlan10通过

[LSW2-GigabitEthernet0/0/1]port trunk allow-pass vlan 20    //允许vlan20通过

save

测试pc1

PC>ping 192.168.10.3



Ping 192.168.10.3: 32 data bytes, Press Ctrl_C to break

From 192.168.10.3: bytes=32 seq=1 ttl=128 time=62 ms

From 192.168.10.3: bytes=32 seq=2 ttl=128 time=63 ms

From 192.168.10.3: bytes=32 seq=3 ttl=128 time=47 ms

From 192.168.10.3: bytes=32 seq=4 ttl=128 time=62 ms

From 192.168.10.3: bytes=32 seq=5 ttl=128 time=63 ms



--- 192.168.10.3 ping statistics ---

  5 packet(s) transmitted

  5 packet(s) received

  0.00% packet loss

  round-trip min/avg/max = 47/59/63 ms



PC>

测试pc2:

PC>ping 192.168.20.4



Ping 192.168.20.4: 32 data bytes, Press Ctrl_C to break

From 192.168.20.4: bytes=32 seq=1 ttl=128 time=62 ms

From 192.168.20.4: bytes=32 seq=2 ttl=128 time=63 ms

From 192.168.20.4: bytes=32 seq=3 ttl=128 time=62 ms

From 192.168.20.4: bytes=32 seq=4 ttl=128 time=47 ms

From 192.168.20.4: bytes=32 seq=5 ttl=128 time=62 ms



--- 192.168.20.4 ping statistics ---

  5 packet(s) transmitted

  5 packet(s) received

  0.00% packet loss

  round-trip min/avg/max = 47/59/63 ms



PC>

vlanif二层交换机拓展三层路由器

sys

[Huawei]sys sw1

[sw1]int g0/0/1

[sw1-GigabitEthernet0/0/1]port link-type access 

[sw1-GigabitEthernet0/0/1]port default vlan 10

[sw1-GigabitEthernet0/0/1]int g0/0/2

[sw1-GigabitEthernet0/0/2]port link-type access

[sw1-GigabitEthernet0/0/2]port default vlan 10

[sw1-GigabitEthernet0/0/2]q

[sw1]int Vlanif 10

[sw1-Vlanif10]ip add 192.168.10.254 24

[sw1-Vlanif10]int Vlanif 20

[sw1-Vlanif20]ip add 192.168.20.254 24



[sw1-Vlanif20]dis ip int b    //查看端口的情况

[sw1]dis ip routing-table     //查看路由表

Route Flags: R - relay, D - download to fib

------------------------------------------------------------------------------

Routing Tables: Public

         Destinations : 6        Routes : 6        



Destination/Mask    Proto   Pre  Cost      Flags NextHop         Interface



      127.0.0.0/8   Direct  0    0           D   127.0.0.1       InLoopBack0

      127.0.0.1/32  Direct  0    0           D   127.0.0.1       InLoopBack0

   192.168.10.0/24  Direct  0    0           D   192.168.10.254  Vlanif10

 192.168.10.254/32  Direct  0    0           D   127.0.0.1       Vlanif10

   192.168.20.0/24  Direct  0    0           D   192.168.20.254  Vlanif20

 192.168.20.254/32  Direct  0    0           D   127.0.0.1       Vlanif20



[sw1]

测试

[sw1]ping 192.168.20.2

  PING 192.168.20.2: 56  data bytes, press CTRL_C to break

    Reply from 192.168.20.2: bytes=56 Sequence=1 ttl=128 time=50 ms

    Reply from 192.168.20.2: bytes=56 Sequence=2 ttl=128 time=40 ms

    Reply from 192.168.20.2: bytes=56 Sequence=3 ttl=128 time=60 ms

    Reply from 192.168.20.2: bytes=56 Sequence=4 ttl=128 time=30 ms

    Reply from 192.168.20.2: bytes=56 Sequence=5 ttl=128 time=50 ms



  --- 192.168.20.2 ping statistics ---

    5 packet(s) transmitted

    5 packet(s) received

    0.00% packet loss

    round-trip min/avg/max = 30/46/60 ms



[sw1]

hybrid接口

LSW1:

sys

[Huawei]sys LSW1

[LSW1]vlan batch 10 20 100

[LSW1]int g0/0/1

[LSW1-GigabitEthernet0/0/1]port link-type hybrid

[LSW1-GigabitEthernet0/0/1]port hybrid pvid vlan 10    //设置pvid值为vlan10的标签

[LSW1-GigabitEthernet0/0/1]port hybrid untagged vlan 10 100    //剥离标签

[LSW1]int g0/0/2

[LSW1-GigabitEthernet0/0/2]port link-type hybrid

[LSW1-GigabitEthernet0/0/2]port hybrid pvid vlan 20    //设置pvid值为vlan10的标签

[LSW1-GigabitEthernet0/0/2]port hybrid untagged vlan 20 100

[LSW1-GigabitEthernet0/0/2]dis vlan    //查看所有vlan端口



[LSW1-GigabitEthernet0/0/2]int g0/0/3

[LSW1-GigabitEthernet0/0/3]port link-type hybrid 

[LSW1-GigabitEthernet0/0/3]port hybrid tagged vlan 10 20 100    //打标签，允许vlan10 20 100 通过

[LSW1-GigabitEthernet0/0/3]dis this    //查看当前配置情况

LSW2：

sys

[Huawei]sys LSW2

[LSW2]vlan ba 10 20 100

[LSW2-GigabitEthernet0/0/3]port link-type hybrid 

[LSW2-GigabitEthernet0/0/3]port hybrid tagged vlan 10 20 100    //打标签

[LSW2-GigabitEthernet0/0/3]int g0/0/1

[LSW2-GigabitEthernet0/0/1]port link-type hybrid 

[LSW2-GigabitEthernet0/0/1]port hybrid pvid vlan 100    //设置pvid

[LSW2-GigabitEthernet0/0/1]port hybrid untagged vlan 10 20 100    //剥离标签

[LSW2-GigabitEthernet0/0/1]dis vlan    //检查

测试：PC1 ping PC2

测试PC1跟PC3是否相通：

本文章纯属个人笔记，如有不当请指正！

编程小号
上一篇 2025-03-15 10:30
下一篇 2025-03-19 17:33

相关推荐

版权声明：本文内容由互联网用户自发贡献，该文观点仅代表作者本人。本站仅提供信息存储空间服务，不拥有所有权，不承担相关法律责任。如发现本站有涉嫌侵权/违法违规的内容， 请发送邮件至 举报，一经查实，本站将立刻删除。
如需转载请保留出处：https://bianchenghao.cn/hz/136601.html