我的华为HG255D开机显示信息

我的华为HG255D开机显示信息我的华为HG255D开机显示信息:U-Boot1.1.3(Oct122011-17:58:01)Board:RalinkAPSoCDRAM: 32MBrelocate_codePointerat:81fb0000configusb.. TheFlashID=0000227E flas


我的华为HG255D开机显示信息:

U-Boot 1.1.3 (Oct 12 2011 – 17:58:01)


Board: Ralink APSoC DRAM:  32 MB

relocate_code Pointer at: 81fb0000

config usb..


 The Flash ID =0000227E 

flash_protect ON: from 0xBF000000 to 0xBF01D46B

protect on 0

*** Warning – bad CRC, using default environment


============================================ 

Ralink UBoot Version: 3.3

——————————————– 

ASIC 3052_MP2 (Port5<->None)

DRAM component: 128 Mbits

DRAM bus: 32 bit

Total memory: 32 MBytes

Flash component: NOR Flash

Date:Oct 12 2011  Time:17:58:01

============================================ 

icache: sets:256, ways:4, linesz:32 ,total:32768

dcache: sets:128, ways:4, linesz:32 ,total:16384 


 ##### The CPU freq = 384 MHZ #### 


 SDRAM bus set to 32 bit 

 SDRAM size =32 Mbytes


@Start First PHY modio study cmd.


 eth_register  

Eth0 (10/100-M)

 enetvar=ethaddr,Eth addr:00:AA:BB:CC:DD:10

 00:AA:BB:CC:DD:10:


 eth_current->name = Eth0 (10/100-M)



 netboot_common, argc= 2 

 *************buf = 0x81fcd620

 **********NexTxPacket = 81fe46c0


 NetTxPacket = 0x81FE46C0 


 NetRxPackets[0] = 0x81FE4CC0


 NetRxPackets[1] = 0x81FE52C0


 NetRxPackets[2] = 0x81FE58C0


 NetRxPackets[3] = 0x81FE5EC0


 NetRxPackets[4] = 0x81FE64C0


 NetRxPackets[5] = 0x81FE6AC0


 NetRxPackets[6] = 0x81FE70C0


 NetRxPackets[7] = 0x81FE76C0


 NetRxPackets[8] = 0x81FE7CC0


 NetRxPackets[9] = 0x81FE82C0


 NetRxPackets[10] = 0x81FE88C0


 NetRxPackets[11] = 0x81FE8EC0


 NetRxPackets[12] = 0x81FE94C0


 NetRxPackets[13] = 0x81FE9AC0


 NetRxPackets[14] = 0x81FEA0C0


 NetRxPackets[15] = 0x81FEA6C0


 NetRxPackets[16] = 0x81FEACC0


 NetRxPackets[17] = 0x81FEB2C0


 NetRxPackets[18] = 0x81FEB8C0


 NetRxPackets[19] = 0x81FEBEC0


 KSEG1ADDR(NetTxPacket) = 0xA1FE46C0 


 NetLoop,call eth_halt ! 


 NetLoop,call eth_init ! 

Trying Eth0 (10/100-M)


 Waitting for RX_DMA_BUSY status Start… done


 Header Payload scatter function is Disable !! 


 ETH_STATE_ACTIVE!! 


Please choose the operation: 

   1: Load system code to SDRAM via TFTP. 

   2: Load system code then write to Flash via TFTP. 

   3: Boot system code via Flash (default).

   4: Entr boot command line interface.

   9: Load Boot Loader code then write to Flash via TFTP. 


## Booting image at bf020000 …

   Image Name:   MIPS OpenWrt Linux-2.6.32.59

   Image Type:   MIPS Linux Kernel Image (lzma compressed)

   Data Size:    773857 Bytes = 755.7 kB

   Load Address: 80000000

   Entry Point:  80000000

   Verifying Checksum … OK

  IH_COMP_LZMA Uncompressing Kernel Image … OK

No initrd

## Transferring control to Linux (at address 80000000) …

## Giving linux memsize in MB, 32


Starting kernel …


Linux version 2.6.32.59 (shcl@shcl-desktop) (gcc version 4.3.3 (GCC) ) #1 Tue May 8 17:10:28 CST 2012

bootconsole [early0] enabled

CPU revision is: 0001964c (MIPS 24Kc)

Ralink RT3052   id:1 rev:3 running at 384.00 MHz

Determined physical RAM map:

 memory: 02000000 @ 00000000 (usable)

Initrd not found or empty – disabling initrd

Zone PFN ranges:

  Normal   0x00000000 -> 0x00002000

Movable zone start PFN for each node

early_node_map[1] active PFN ranges

    0: 0x00000000 -> 0x00002000

Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128

Kernel command line: console=ttyS1,57600 rootfstype=squashfs,jffs2 board=HG255D

PID hash table entries: 128 (order: -3, 512 bytes)

Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)

Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)

Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.

Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes

Writing ErrCtl register=000022a0

Readback ErrCtl register=000022a0

Memory: 30096k/32768k available (1819k kernel code, 2672k reserved, 325k data, 132k init, 0k highmem)

SLUB: Genslabs=7, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1

Hierarchical RCU implementation.

NR_IRQS:48

console [ttyS1] enabled, bootconsole disabled

console [ttyS1] enabled, bootconsole disabled

Calibrating delay loop… 255.59 BogoMIPS (lpj=1277952)

Mount-cache hash table entries: 512

NET: Registered protocol family 16

MIPS: machine is HuaWei HG255D

bio: create slab <bio-0> at 0

Switching to clocksource MIPS

NET: Registered protocol family 2

IP route cache hash table entries: 1024 (order: 0, 4096 bytes)

TCP established hash table entries: 1024 (order: 1, 8192 bytes)

TCP bind hash table entries: 1024 (order: 0, 4096 bytes)

TCP: Hash tables configured (established 1024 bind 1024)

TCP reno registered

NET: Registered protocol family 1

squashfs: version 4.0 (2009/01/31) Phillip Lougher

Registering mini_fo version $Id$

JFFS2 version 2.2. (NAND) (SUMMARY)  漏 2001-2006 Red Hat, Inc.

msgmni has been set to 58

io scheduler noop registered

io scheduler deadline registered (default)

Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled

serial8250: ttyS0 at MMIO 0x10000500 (irq = 13) is a 16550A

serial8250: ttyS1 at MMIO 0x10000c00 (irq = 20) is a 16550A

physmap platform flash device: 01000000 at bf000000

physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank

 CFI mfr 0x00000001

 CFI id  0x00002101

 Amd/Fujitsu Extended Query Table at 0x0040

  Amd/Fujitsu Extended Query version 1.3.

physmap-flash.0: CFI does not contain boot bank location. Assuming top.

number of CFI chips: 1

cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.

RedBoot partition parsing not available

Using physmap partition information

Creating 6 MTD partitions on “physmap-flash.0”:

0x000000000000-0x000000020000 : “u-boot”

0x000000020000-0x000000120000 : “kernel”

0x000000120000-0x000000fa0000 : “rootfs”

mtd: partition “rootfs” set to be root filesystem

mtd: partition “rootfs_data” created automatically, ofs=6A0000, len=900000 

0x0000006a0000-0x000000fa0000 : “rootfs_data”

0x000000020000-0x000000fa0000 : “firmware”

0x000000fa0000-0x000000fc0000 : “factory”

0x000000000000-0x000001000000 : “fullflash”

TCP westwood registered

NET: Registered protocol family 17

802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>

All bugs added by David S. Miller <davem@redhat.com>

VFS: Mounted root (squashfs filesystem) readonly on device 31:2.

Freeing unused kernel memory: 132k freed

Please be patient, while OpenWrt loads …

Button Hotplug driver version 0.3.1

– preinit –

Registered led device: hg255d:power

Registered led device: hg255d:internet

Registered led device: hg255d:wlan

Registered led device: hg255d:usb

Registered led device: hg255d:wps

Registered led device: hg255d:voice

Press the [f] key and hit [enter] to enter failsafe mode

– regular preinit –

switching to jffs2

mini_fo: using base directory: /

mini_fo: using storage directory: /overlay

– init –


Please press Enter to activate this console. device eth0.1 entered promiscuous mode

device eth0 entered promiscuous mode

br-lan: port 1(eth0.1) entering forwarding state

Compat-wireless backport release: compat-wireless-2011-11-29

Backport based on wireless-testing.git master-2011-12-01

cfg80211: Calling CRDA to update world regulatory domain

SCSI subsystem initialized

usbcore: registered new interface driver usbfs

usbcore: registered new interface driver hub

usbcore: registered new device driver usb

cfg80211: World regulatory domain updated:

cfg80211:     (start_freq – end_freq @ bandwidth), (max_antenna_gain, max_eirp)

cfg80211:     (2402000 KHz – 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)

cfg80211:     (2457000 KHz – 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)

cfg80211:     (2474000 KHz – 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)

cfg80211:     (5170000 KHz – 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)

cfg80211:     (5735000 KHz – 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)

usbcore: registered new interface driver rt73usb

usbcore: registered new interface driver rtl8187

Registered led device: rt2800pci-phy0::radio

Registered led device: rt2800pci-phy0::assoc

Registered led device: rt2800pci-phy0::quality

usbcore: registered new interface driver rt2800usb

RPC: Registered udp transport module.

RPC: Registered tcp transport module.

RPC: Registered tcp NFSv4.1 backchannel transport module.

NTFS driver 2.1.29 [Flags: R/O MODULE].

PPP generic driver version 2.4.2

tun: Universal TUN/TAP device driver, 1.6

tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>

Installing knfsd (copyright (C) 1996 okir@monad.swb.de).

gpiodev: gpio device registered with major 254

gpiodev: gpio platform device registered with access mask FFFFFFFF

ip_tables: (C) 2000-2006 Netfilter Core Team

NET: Registered protocol family 24

nf_conntrack version 0.5.0 (472 buckets, 1888 max)

CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use

nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or

sysctl net.netfilter.nf_conntrack_acct=1 to enable it.

xt_time: kernel timezone is -0000

xt_opendpi 0.1 (OpenDPI wrapper module).

dwc_otg: version 2.72a 24-JUN-2008 (Patched by Lintel 2011)

dwc_otg: Core Release: 2.66a

dwc_otg: Periodic Transfer Interrupt Enhancement – disabled

dwc_otg: Multiprocessor Interrupt Enhancement – disabled

dwc_otg: Using DMA mode

dwc_otg: Device using Buffer DMA mode

dwc_otg dwc_otg.0: DWC OTG Controller

dwc_otg dwc_otg.0: new USB bus registered, assigned bus number 1

dwc_otg dwc_otg.0: irq 26, io mem 0x101c0000

dwc_otg: Init: Port Power? op_state=1

dwc_otg: Init: Power Port (0)

usb usb1: configuration #1 chosen from 1 choice

hub 1-0:1.0: USB hub found

hub 1-0:1.0: 1 port detected

usbcore: registered new interface driver usblp

Initializing USB Mass Storage driver…

usbcore: registered new interface driver usb-storage

USB Mass Storage support registered.

usbcore: registered new interface driver ums-alauda

usbcore: registered new interface driver ums-cypress

usbcore: registered new interface driver ums-datafab

usbcore: registered new interface driver ums-freecom

usbcore: registered new interface driver ums-isd200

usbcore: registered new interface driver ums-jumpshot

usbcore: registered new interface driver ums-karma

usbcore: registered new interface driver ums-sddr09

usbcore: registered new interface driver ums-sddr55

usbcore: registered new interface driver ums-usbat

fuse init (API version 7.13)

device wlan0 entered promiscuous mode

br-lan: port 2(wlan0) entering forwarding state

device wlan0 left promiscuous mode

br-lan: port 2(wlan0) entering disabled state

device wlan0 entered promiscuous mode

br-lan: port 2(wlan0) entering forwarding state




BusyBox v1.15.3 (2012-05-08 16:14:49 CST) built-in shell (ash)

Enter ‘help’ for a list of built-in commands.


           _.-“._

        _-: ()   “:_

     _-“‘. ‘.   _”  :-_

   -”     ‘.-.’-. .’   “-_

  |”_()   _’).:(.’  ()   -“|

  J  “_ .’  .”. ‘.    -”  F

   L   “_ .’ () ‘. ‘_-” o J

   | o ‘ “-_     _:”:     |

    “_ L ‘  “-.-” | J  _-“

      “| J    F ()J :-“

        “| () J   :-” 

          “-_ | _” 

             “-“

  Openwrt-Dreambox(2012, r443) ——————–

  * Base on Openwrt Backfire 

  * lintel(lintel.huang@gmail.com).

  * yuef zhu(flyzjhz@gmail.com).

  * XEyE(xeye.wang@gmail.com).

  * Vcore(vcore85@gmail.com).

  * emongxx(emongxx@gmail.com).

 —————————————————

root@DreamBox:/# 

版权声明:本文内容由互联网用户自发贡献,该文观点仅代表作者本人。本站仅提供信息存储空间服务,不拥有所有权,不承担相关法律责任。如发现本站有涉嫌侵权/违法违规的内容, 请发送邮件至 举报,一经查实,本站将立刻删除。
如需转载请保留出处:https://bianchenghao.cn/37172.html

(0)
编程小号编程小号

相关推荐

发表回复

您的电子邮箱地址不会被公开。 必填项已用*标注